How to make a PEX-AL-PEX compression fitting connection

Tools and materials required:

PEX-AL-PEX tubing

PEX cutter

PEX-AL-PEX compression fitting

PEX-AL-PEX reamer

(2) Adjustable crescent wrenches or similar (12-14”)

Safety first - always wear appropriate eye protection gear.

Step 1: Cut the pipe

Position the pipe cutter perpendicular to the pipe and make a smooth, clean cut.Cut pipe should be free from burrs.

Step 2: Ream the pipe

Select appropriate size reamer inlet and insert it fully into the PEX-AL-PEX pipe.The edge of the pipe must touch the reamers’ blade as shown.

While holding the pipe, firmly push the reamer in and give it 2-3 full turns (in any direction). Shavings indicate that the procedure is being performed properly.This is how the reamed pipe should look like. Reaming returns the pipe to its’ original round shape and prepares it for installation of the fitting.

Step 3: Install the compression fitting

First, slide the compression nut over the pipe. Second, slide the split O-ring as shown on the picture.Fully insert the main body of the PEX-AL-PEX compression fitting into the pipe.

Step 4: Tighten the compression nut

Slide the nut and O-ring toward the fitting and tighten the compression nut over the fitting by hand (~ 2 full turns).

Position one crescent wrench over the fitting and the other over the compression nut. Tighten the compression nut (~ 1-1.5 full turns). You can use a marker to indicate a starting point.

Step 5: Connection is complete

This is how a finished connection should look like. Always inspect the fitting visually after the work is complete.

 

Frequently Asked Questions:

Q: Is PEX-AL-PEX reamer necessary? Can I use a standard pipe reamer?

A: PEX-AL-PEX reamer performs (2) functions – it reams the pipe inside and outside (which can be done with a standard pipe reamer), but also returns the pipe to a round shape, which cannot be accomplished with a standard pipe reamer. Since PEX-AL-PEX tubing can be deformed when being bent or cut, it must be “rounded” in order for the fitting to fit inside the pipe properly.

Q: Are PEX-AL-PEX compression fittings reusable?

A: It is possible to disconnect the fitting but it could be quite difficult, and so for practical reasons, the answer would be no.

Q: Are these fittings suited for potable water applications?

A: No. They do not meet the lead content limitations and therefore are not approved for potable water use.

Q: Is there a possibility of over- or under-tightening the fitting?

A: If you follow the instructions above, the risks of over- or under-tightening are very small. Since all systems must be pressure tested prior to being put into use, it is possible to tighten the fitting more if there’s a leak at the connection point. In order to avoid over-tightening the compression nut, do not use excessive force and wrenches larger than indicated when installing the fitting.

Q: Should I apply any thread sealant, Teflon tape or glue to the compression fittings’ threads?

A: No. Not only these are unnecessary, they may compromise the integrity of the connection. Thread sealant and tape can (and in fact, must) be applied over the MNPT/FNPT threaded portion of the fitting, which connects to another pipe or fitting.

Q: What must be the minimal opening of the wrench?

A: For 1” PEX-AL-PEX fittings, which is the largest size we carry, the compression nut requires a minimum of 25/16” (or 1-1/2” and 1/16”) opening. Adjustable pliers (like the Channellock®) can also be used.

Q: Which connection method is better for PEX-AL-PEX – compression or press?

A: Press fittings are more expensive and require an expensive PEX tool, but are quicker and easier to install and therefore are best suited for high-volume installations where pricing is not an issue. Compression fittings require somewhat more time and labor but cost substantially less and do not require a special PEX-AL-PEX tool. You can find more information on different PEX connection methods here.

Q: I see that the brass O-ring is split - is it normal?

A: Yes. When the compression nut is tightened, the open ends of the O-ring come together, exerting pressure upon the PEX-AL-PEX pipe, allowing it to be compressed over the fitting's barbs.

Q: What purpose do the black rubber O-rings over the fitting's barbs serve?

A: The O-rings are intended to prevent water leakage. The main purpose of the barbs is to prevent the fitting from popping out under pressure from the pipe. The O-rings should not be removed from the fitting, nor is it necessary to lubricate them in any way.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

خط تولید  ، خدمات فنی و مهندسی ،کارخانه تولید ،خط تولید لوله پنج لایه pex،خط تولید لوله پکس ،محصولات پلیمری ،صنعت پلیمر ، محصولات لاستیک و پلاستیک ، ماشین آلات تولید ،راه اندازی کارخانه ، نصب و راه اندازی خط تولید ، مشاوره صنعتی ، مشاوره تولیدی ،سرمایه گذاری صنعتی و تولیدی ، طرح توجیهی ، پروژه صنعتی ، سازنده خط تولید ،سازنده ماشین آلات ،اکسترود تولید ،سازنده اکسترودر تولید ،اکستروژن ،سازنده،پلیمر ،تکنولوژی تولید ،فرآیند تولید ،تجهیزات صنعتی،

, production line FIVE LAYER PIPE ,PEX FIVE LAYER PIPE ,TUBING PEX ,PEX piping, ,PEX_AL_PEX  ,PEX TUBE,production line ,PRODUCTION LINE POLYMER ,Trading Company, ,Production plan design ,Production Project ,Industrial project ,Technical Services ,Engineering services ,production technology ,Production Process ,Industrial equipment ,Machinery, ,Machine ,Setup Factory ,Installation production line Industry,Extrude,extrusion ,Industry, ,Manufacturer, machines and

,Pex pipe machinery, Pex pipe machine,

خط توليد لوله پنج لايه و تک لایه آلومینیوم و پکس pex ، ماشین آلات توليد لوله پنج لایه و تک لایه پکس PEX ، دستگاه تولید لوله هاي پنج لايه ، کارخانه تولید لوله پنج لایه PEX ، خط تولید لوله تک لایه PEX خط-تولید-دستگاه-لوله-پنج-لایه-پکس-

FIVE LAYER PIPE , ، PIPE PEX-AL-PEX ، pex five layer pipe production line, pex piping production machine  pex pipe، pex tube machinery، PEX tubing، PIPE MANUFACTURE

pex-al-pex-pipe-five-layer-production-line-machinery-machine- piping-tubing-tube-Manufacturer
خط توليد پروفيل در و پنجره upvc، خط توليد داکت برق، خط توليد پنل ديوارپوش ، پانل ديواري و سقف کاذب pvc، خط توليد لوله پليکا PVC، خط توليد لوله تک لايه و پنج لايه  PEX پکس،خط توليد لوله PEX AL PEX، خط توليد لوله يک لايه وچند لايه پلي اتيلن و پلي پروپيلن و پکس PP,PE,PEX، دستگاه لمينيت پانل، دستگاه هات استمپ پانل PVc خط UV ، هاي لايت يا براق پانل