PEX Tubing Technical Specifications
PEX Tubing Technical Specifications
and General Installation Recommendations
Since all PEX tubing used in the US is manufactured to the same ASTM and dimensional (SDR) standards, these specifications are universal. Manufacturing tolerances and other details can be found in manufacturers’ manuals.
Dimensional data and specifications
PEX Tubing size
(CTS/Nominal) |
Outside Diameter
(OD) |
Minimum wall thickness |
Inside Diameter
(ID) |
Volume gal/100ft |
Weight lbs/100ft |
| 3/8" |
0.500" |
0.070" |
0.360" |
0.50 |
4.50 |
| 1/2" |
0.625" |
0.070" |
0.485" |
0.92 |
5.80 |
| 5/8" |
0.750" |
0.083" |
0.584" |
1.34 |
8.38 |
| 3/4" |
0.875" |
0.097" |
0.681" |
1.83 |
11.00 |
| 1" |
1.125" |
0.125" |
0.875" |
3.03 |
17.06 |
* Numbers are approximate as per ASTM requirements. Dimensional data is subject to manufacturing tolerances and may vary by brand. Same data applies both to oxygen barrier and non-barrier PEX.
Notes:
- PEX piping sizes are denoted by CTS (copper tubing size), not OD (Outside Diameter) or ID (Inside Diameter).
- OD of PEX, copper and CPVC pipe with the same size (CTS) is the same. This is why push fittings can be used with all of these pipes.
- PEX made to US standards must comply with a SDR-9 (Standard Dimension Ratio), which is the ratio of OD (Outside Diameter) to pipe wall thickness (9:1). Exceptions are nominal sizes 1/2" and below.
Pressure ratings, testing and pressure drop
| PEX Tubing Pressure Ratings |
Pressure testing - Hydronic & Radiant Heating |
Pressure testing - Hot & Cold Water Plumbing |
200°F at 80 psi
180°F at 100 psi
74°F at 160 psi |
3 times the maximum working pressure or a minimum of 40 psi, but no greater than 100 psi.
Duration: 30 minutes minimum, 2 hours recommended |
1.5 times the maximum working pressure but no greater than pipe’s pressure rating at given temperature.
Duration: 30 minutes minimum, 2 hours recommended |
Notes:
- Maximum working pressure indicates highest anticipated operating pressure.
- Pressure testing requirements and procedures should be in compliance with local codes and PEX manufacturer’s instructions.
- Air pressure testing is recommended over water for practical reasons and due to difficulties arising from water freezing during winter months.
- Since PEX is a flexible pipe, it will expand somewhat (especially PEX-a) during the initial pressurizing of the system, causing a drop in pressure reading. Some manufacturers recommend "conditioning" of the system, or allowing the PEX system to stay pressurized for about 30 minutes prior to taking a reading.
- For concrete slabs, pressure is maintained at 30 psi during the pour and is monitored to assure integrity of the system.
Pressure Drop Table (psi per 100ft of tubing length)
| Flow rate, GPM |
PEX tubing size |
| 3/8" |
1/2" |
5/8" |
3/4" |
1" |
| 0.5 |
2.50 |
0.51 |
0.21 |
0.05 |
0.02 |
| 1.0 |
7.50 |
1.70 |
0.71 |
0.34 |
0.10 |
| 2.0 |
26.1 |
5.30 |
2.12 |
1.02 |
0.35 |
| 3.0 |
54.1 |
11.0 |
4.36 |
2.10 |
0.63 |
| 4.0 |
|
18.4 |
7.36 |
3.53 |
1.06 |
| 5.0 |
|
27.4 |
11.0 |
5.26 |
1.58 |
| 6.0 |
|
38.1 |
15.3 |
7.30 |
2.19 |
| 7.0 |
|
|
20.1 |
9.63 |
2.89 |
| 8.0 |
|
|
25.6 |
12.3 |
3.68 |
| 9.0 |
|
|
31.7 |
15.1 |
4.55 |
| 10.0 |
|
|
|
18.3 |
5.50 |
| 11.0 |
|
|
|
21.7 |
6.52 |
| 12.0 |
|
|
|
25.4 |
7.63 |
| 13.0 |
|
|
|
|
8.81 |
| 14.0 |
|
|
|
|
10.1 |
| 15.0 |
|
|
|
|
11.4 |
1 psi = 2.3 ft of head (for fresh water), or 1 ft of head = 0.434 psiBending radius
| Tubing size |
Minimum bending radius |
Minimum bending diameter (OC) |
| 3/8" |
4" |
8" |
| 1/2" |
5" |
10" |
| 5/8" |
6" |
12" |
| 3/4" |
7" |
14" |
| 1" |
9" |
18" |
Minimum recommended bending radius is 8 times the outside diameter of PEX
(8 x OD). For 1/2" PEX with OD of 5/8", minimum bending radius is 8 x 5/8" = 5".
Over-bending the PEX pipe, deforms its’ round shape, restricts flow and over-stresses the pipe.
Note: minimum bending diameter only refers to the 90-degree and 180-degree (U-shaped) bends. Parallel runs of pipe can be spaced as close as necessary.
Elongation (linear expansion)
Typical elongation is anywhere from 1" to 2.5" for every 100ft of PEX pipe at a 10°F temperature rise.
Since PEX expands and contracts with temperature changes, it should be secured so as to provide sufficient space for expansion to occur.
Connection Systems and Compatibility
All types (A, B, C) of PEX pipe are compatible with Crimp, Clamp or Push-to-connect type connection systems:
- Crimp system: Crimp Tool + Copper Crimp Rings (per ASTM F1807 standard) + Crimp style PEX Fittings (brass – per F877/F1807 or poly – per F877/F2159 standards).
- Clamp (Cinch) system: Clamp Tool + Stainless Steel Clamps (per ASTM F2098) + Crimp style PEX Fittings (same as above).
- Push system: Push-Fit or Push-to-Connect style fittings (no tools or rings required)
Standards, Approvals & Certifications (Everhot PEX)
ASTM F876: Standard Specification for Crosslinked Polyethylene (PEX) Tubing.
ASTM F877: Standard Specification for Crosslinked Polyethylene PEX Hot- and Cold- Water Distribution Systems.
ASTM F2023: Oxidative resistance of PEX to Hot Chlorinated Water per NSF protocol P171 (Non-Barrier PEX Tubing).
CSA B137.5: Crosslinked Polyethylene PEX Tubing Systems for Pressure Applications.
NSF/ANSI 14, nsf-rfh: Evaluated for use in Radiant Floor Heating (NSF-rfh) Applications (Oxygen Barrier PEX tubing).
NSF/ANSI 61-G, NSF/ANSI 372, nsf-pw-g: Complies with NSF/ANSI standard 61-G for Lead-Free Drinking Water System Components (Non-Barrier PEX Tubing).
UPC listed by IAPMO (International Association of Plumbing and Mechanical Officials).
PEX tube|PEX pipe|PEX tubing|PEX piping|PEX-AL-PEX|PEX plumbing|PEX fittings|PEX heating|PEX single layer pipe|multilayer pipe|composite pipe|multilayer composite pipe|five layer pipe|radiant heating|five layer pipe production line|PEX-AL-PEX pipe production line|PEX tube production line|
PEX-AL-PEX multilayer pipe|
PEX pipe connection |multilayer pipe production line|
multi-layer PEX-AL-PEX pipe|multi-layer PEX-aluminum composite pipe|multi-layer PEX pipe|
PEX/Aluminum/PEX|PEX plumbing systems|PEX piping systems|